Connecting Cables
   
   
Connect the power cord for your monitor to the POWER port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Use appropriate connection for your computer.
 
Using the RGB (Analog) connector on the video card.
- Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor.

[ RGB IN ]
Using the DVI (Digital) connector on the video card.
- Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor.

[ DVI IN(HDCP) ]
Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the RGB connection cable.
If the monitor and the computer are connected, you can turn them on and use them
 



Connecting a Speaker


When connecting a speaker, be careful that the grooves of the monitor and the speaker .
()are aligned with each other.
Adjust the aligned positions until you hear a ‘click’. If a speaker is connected correctly, you can hear a ‘click’.If a speaker is connected without you hearing a ‘click’, the holding part may become damaged.
If you need to separate, please pull () a little and push to the right.


 
MIC / SPK
 
Connect the red cable of the cables provided when the speaker was purchased to the audio output terminal at the back of the computer.
Connect the other end of the cable to the red terminal at the back of the speaker.
   
Connect the light green cable of the cables provided when purchasing the speaker to the audio output terminal at the back of the computer.
Connect the other end of the cable to the light green terminal at the back of the speaker.
/
 
Connect a headphone to the black terminal at the right of the speaker.
   
Connect a microphone to the red terminal at the right of the speaker.
By turning part ( + , - ) in the direction shown in the figure below, the speaker turns on and the volume increases.
Connect the power line connected to the speaker to the black terminal of the monitor.
This speaker is not connected to an external power source. It is connected to a monitor for the required power.


 
   
Using the Stand


Sliding stand
  Stand Stopper



Swivel stand

Using (),You can swivel the monitor left and right at an angle of 90° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide.
When you try to rotate the monitor in the state of the power cord or cable connecting to the monitor, the power cord of cable can be destroyed.



Tilt angle

Using (), You can adjust the tilt anlgle within a range of 3° forward to 25° backward for the most comfortable viewing angle.




Attaching a Base

This monitor accepts a 200 mm x 100 mm VESA-compliant Mounting interface pad.


      Monitor
         
      Mounting interface pad (Sold separately)


1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.

To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface.
Contact the nearest Samsung Service Center for more information.
Samsung Electronics will not be responsible for damages caused by using a base other than those specified.
Please use Wall Mount according to the International standards.

 
 
Installing the Monitor Driver (Automatic)
   
 
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
   
  Prepare a blank disk and download the driver program file at the Internet web site shown below.
   
 
  • Internet web site :
    		• http://www.samsung.com/ (Worldwide)
    http://www.samsung.com/monitor (U.S.A)
    http://www.sec.co.kr/monitor (Korea)
    http://www.samsungmonitor.com.cn/ (China)
       
     
      1. Insert CD into the CD-ROM drive.
      2. Click "Windows".
      3. Choose your monitor model in the model list, then click the "OK" button.



      4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button (Microsoft® Windows® XP/2000 Operating System).

           
        This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor momepage
        http://www.samsung.com/

      5. Monitor driver installation is completed.
       
       
       
    Installing the Monitor Driver (Manual)
     
     

    Windows Vista | Windows XP | Windows 2000 |Windows Me |Windows NT | Linux  
       
    Microsoft® Windows Vista™ Operating System
       
     
    1. Insert your Manual CD into your CD-ROM drive.
    2. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".

         

    3. Click "Personalization" and then "Display Settings".

         

    4. Click "Advanced Settings…".

         

    5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is.
      If the message “Windows needs…” is displayed, as shown in the figure below,
      click "Continue".

         

      This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
      The certified driver will be posted on Samsung Monitor homepage
      http://www.samsung.com/

    6. Click "Update Driver…" in the "Driver" tab.

         

    7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".

         

    8. Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".

       

    9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next".


         

    10. Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence.

       
       
       
    Microsoft ® Windows ® XP Operating System
       
     
    1. Insert CD into the CD-ROM drive.
    2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.

         

    3. Click "Display" icon and choose the "Settings" tab then click "Advanced...".

         

    4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

         

    5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button.

         

    6. Select "Don't search ,I will..." then click "Next" and then click "Have disk".

         

    7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.

         

    8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.



      This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
      The certified driver will be posted on Samsung Monitor homepage
      http://www.samsung.com/
    9. Click the "Close" button then click "OK" button continually.



         

    10. Monitor driver installation is completed.
       
    Microsoft ® Windows ® 2000 Operating System
       
      When you can see "Digital Signature Not Found" on your monitor, follow these steps.
         
       
    1. Choose "OK" button on the "Insert disk" window.
    2. Click the "Browse" button on the "File Needed" window.
    3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
         
      How to install
         
       
    1. Click "Start" , "Setting" , "Control Panel".
    2. Double click the "Display" icon.
    3. Select the "Settings" tab and click "Advanced Properties" button.
    4. Choose "Monitor".
      Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation
      Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually.
    5. Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
    6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk".
    7. Click the "Browse" button then choose A:(D:\Driver).
    8. Click the "Open" button, then click "OK" button.
    9. Choose your monitor model and click the "Next" button then click "Next" button.
    10. Click the "Finish" button then the "Close" button.

      If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button.
         
    Microsoft ® Windows ® Millennium Operating System
         
     
    1. Click "Start" , "Setting" , "Control Panel".
    2. Double click the "Display" icon.
    3. Select the "Settings" tab and click "Advanced Properties" button.
    4. Select the "Monitor" tab.
    5. Click the "Change" button in the "Monitor Type" area.
    6. Choose "Specify the location of the driver".
    7. Choose "Display a list of all the driver in a specific location..." then click "Next" button.
    8. Click the "Have Disk" button.
    9. Specify A:\(D:\driver) then click "OK" button.
    10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK".
    11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
         
    Microsoft ® Windows ® NT Operating System
         
     
    1. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
    2. In Display Registration Information window, click Settings Tab and then click "All Display Modes".
    3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK".
    4. Click "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency).
      If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.
         
    Linux Operating System
         
      To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
         
     
    1. Press "Enter" at the first and the second screen after executing the X86Config file.
    2. The third screen is for setting your mouse.
    3. Set a mouse for your computer.
    4. The next screen is for selecting a keyboard.
    5. Set a Keyboard for your computer.
    6. The next screen is for setting your monitor.
    7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
    8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
    9. "Enter" the model name of your monitor. This information will not affect the actual execution of X-Window.
    10. You have finished setting up your monitor.
      Execute X-Window after setting other requested hardware.
       
    		 
       
    		© 1995~2007 SAMSUNG. ALL Right Reserved