Connecting the Monitor
   
   
 
Connect the DC adapter for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.

Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the RGB IN port on the back of your monitor.

Using the DVI (Digital) connector on the video card.
Connect the DVI cable to the DVI IN port on the back of your monitor.

Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.
Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Cable Fix Ring
When connecting the cable is finished fix
the cables to the Cable Fix Ring.
 
   
Using the Stand
     
  Removing the base
   
 
   
 
Turn off your monitor and unplug its power cord.
Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
Remove two screws and then remove the Stand from the LCD monitor.
   
  Pivot Stand/Sliding Stand
     
 
   
A. Stand Stopper
 
 

The Auto Ratation may not be supported depend on the monitor model.

     
  * If you rotate the screen without lifting it to its maximum height, the screen may be damaged
because the edge of the screen would hit the floor.
     
  Attaching a Base
   
 

This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad.

   
 
   
 
    A. Monitor
    B. Mounting interface pad (Sold separately)
   
 
Turn off your monitor and unplug its power cord.
Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
Remove four screws and then remove the stand from the LCD monitor.
Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
   
Installing the Monitor Driver (Automatic)
   
 
When prompted by the operating system for the monitor driver, insert the CD-ROM included
with this monitor. Driver installation is slightly different from one operating system to another.
Follow the directions appropriate for the operating system you have.
   
  Prepare a blank disk and download the driver program file at the Internet web site shown here.
   
 
  • Internet web site :
  • http://www.samsung.com/ (Worldwide)
    http://www.samsung.com/monitor (U.S.A)
    http://www.sec.co.kr/monitor (Korea)
    http://www.samsungmonitor.com.cn/ (China)
       
    Windows ME
       
     
      1. Insert CD into the CD-ROM drive.
      2. Click "Windows ME Driver".
      3. Choose your monitor model in the model list, then click the "OK" button.



      4. Click the "Install" button in the "Warning" window.



      5. Monitor driver installation is completed.
       
    Windows XP/2000
       
     
      1. Insert CD into the CD-ROM drive.
      2. Click "Windows XP/2000 Driver"
      3. Choose your monitor model in the model list, then click the "OK" button.



      4. If you can see following message window, then click the "Continue Anyway" button.
        Then click "OK" button.

           
        This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor momepage
        http://www.samsung.com/

      5. Monitor driver installation is completed.
       
    Installing the Monitor Driver (Manual)
       
     
     

    Windows XP | Windows 2000 |Windows Me |Windows NT | Linux  
       
    When prompted by the operating system for the monitor driver, insert the CD-ROM included
    with this monitor. Driver installation is slightly different from one operating system to another.
    Follow the directions appropriate for the operating system you have.
       
      Prepare a blank disk and download the driver program file at the Internet web site shown here.
       
     
  • Internet web site :
  • http://www.samsung.com/ (Worldwide)
    http://www.samsung.com/monitor (U.S.A)
    http://www.sec.co.kr/monitor (Korea)
    http://www.samsungmonitor.com.cn/ (China)
       
    Microsoft® Windows® XP Operating System
       
     
    1. Insert CD into the CD-ROM driver.
    2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.

         

    3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".

         

    4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

         

    5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.

         

    6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".

         

    7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the
      model list and click the "Next" button.

         

    8. If you can see following "Message" window, then click the "Continue Anyway" button.
      Then click "OK" button.



      This monitor driver is under certified MS logo,and this installation doesn't damage your system.
      The certified driver will be posted on Samsung Monitor homepage.
      http://www.samsung.com/

    9. Click the "Close" button then click "OK" button continually.



         

    10. Monitor driver installation is completed.
       
    Microsoft® Windows® 2000 Operating System
       
      When you can see "Digital Signature Not Found" on your monitor, follow these steps.
         
       
    1. Choose "OK" button on the "Insert disk" window.
    2. Click the "Browse" button on the "File Needed" window.
    3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
         
      How to install
         
       
    1. Click "Start" , "Setting" , "Control Panel".
    2. Double click the "Display" Icon.
    3. Choose the "Settings" tab and then click "Advanced..".
    4. Choose "Monitor".
      Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation
      Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually.
    5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
    6. Choose "Display a list of the known drivers for this device so that I can choose a
      specific driver
      " then click "Next" and then click "Have disk".
    7. Click the "Browse" button then choose A:(D:\Driver).
    8. Click the "Open" button, then click "OK" button.
    9. Choose your monitor model and click the "Next" button then click "Next" button.
    10. Click the "Finish" button then the "Close" button.
    If you can see the "Digital Signature Not Found" window then click the "Yes"button.
    And click the "Finish" button then the "Close" button.
         
    Microsoft® Windows® Millennium Operating System
         
     
    1. Click "Start" , "Setting" , "Control Panel".
    2. Double click "Display" icon.
    3. Select the "Settings" tab and click "Advanced Properties" button.
    4. Select the "Monitor" tab.
    5. Click the "Change" button in the "Monitor Type" area.
    6. Choose "Specify the location of the driver".
    7. Choose "Display a list of all the driver in a specific location.." then click "Next" button.
    8. Click the "Have Disk" button
    9. Specify A:\(D:\driver) then click "OK" button.
    10. Select "Show all devices" and choose the monitor that corresponds to the one you
      connected to your computer and click "OK".
    11. Continue choosing "Close" button and "OK" button until you close the Display Properties
      dialogue box.
         
    Microsoft® Windows® NT Operating System
         
     
    1. Click Start, Settings, Control Panel, and then double-click Display icon.
    2. In Display Registration Information window, click Settings Tab and then click All Display Modes.
    3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
      and then click OK.
    4. Click Apply button if you see the screen working normally after clicking Test.
      If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency).
         
    Linux Operating System
         
     
    1. Press Enter at the first and the second screen after executing the X86Config file.
    2. The third screen is for setting your mouse.
    3. Set a mouse for your computer.
    4. The next screen is for selecting a keyboard.
    5. Set a Keyboard for your computer.
    6. The next screen is for setting your monitor.
    7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
    8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
    9. Enter the model name of your monitor. This information will not affect the actual execution
      of X-Window.
    10. You have finished setting up your monitor.
      Execute X-Window after setting other requested hardware.
       
       
    Natural Color
       
     
    Natural Color Software Program
       
     

    One of the recent problems in using a computer is that the color of the images printed out by a printer or
    other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
    The Natural Color S/W is the very solution for this problem. It is a color administration system developed
    by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute
    (ETRI). This system is available only for Samsung monitors and makes the color of the images on the
    monitor the same as the printed or scanned images.
    For more information, refer to Help (F1) in the software program.

    How to install the Natural Color software
    Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen
    of the program Natural Color will be executed. Click Natural Color on the initial screen to install the
    Natural Color software.
    To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive,
    click the [Start] button of Windows and then select [Execute].
    Enter D:\color\eng\setup.exe and then press the <Enter> key.
    (If the drive where the CD is inserted is not D:\, enter the applicable drive.)

    How to delete the Natural Color software program
    Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
    Select Natural Color from the list and then click the "Add/Delete" button.

       
     
       
    © 1995~2005 SAMSUNG.ALL Right Reserved